![]() It’s important to remember that you don’t have to use the floating selection method if you don’t want to. It might take a bit to get used to thinking about it this way, but practice makes perfect! Using Pixel Layers Moving right or down uses positive numbers, while left and up use negative numbers. To move your selection 25 pixels to the right and 40 pixels up, you’d enter 25 in the X box and -40 in the Y box. Make sure that you’re in Offset mode and not Angle or Vanishing Point, and then stick to editing the X and Y settings. Typically this tool is used for precise 3D distortions of your selection, but you can use it to move your selections with pixel-level accuracy. If you’re finding the Move tool isn’t letting you move your selection, there are a couple of options located in the tool palette that might help. If you try to use it before that, you’ll simply move your selection area instead of the actual contents, or you’ll move the entire image, depending on the Move tool mode. What About the Move Tool?ĭespite the fact that GIMP has a Move tool, you can only use it to move your selection once you’ve already floated it. It makes much more sense to me to separate your selection into a new layer permanently, but I’ll explain that in more detail later on. Personally, I find this workflow a bit limited, but it can be handy if you’re just making a single change and you want to finish up as quickly as possible. You can create a new layer using your floating selection using the green new layer button in the bottom left of the Layers palette, anchor your floating selection to resume editing the whole image, or delete your floating selection (which also deletes the selection contents). The Layers palette displaying my floating selection The fastest way to do this is to hold down the Ctrl and Alt keys (Command and Option on a Mac) and simply click and drag with your mouse to move the area you’ve selected. ![]() Once you’ve got it just right, the next step is to turn your selection into something GIMP calls a “floating selection”. Holding down the Shiftkey while drawing a new selection will add to your existing selection, and holding down the Ctrlkey will subtract from it. If you want to adjust your selection area, you can tweak it using the handles, or combine it with another selection. For bonus points, try using the Selection Editor! These instructions work with all selection tools in GIMP, so feel free to experiment with different combinations. The simplest way to move a selection in GIMP starts, unsurprisingly, with making your selection using any of the selection tools. Since it’s such a common operation, there are quite a few different ways that you can make a selection and move it around your image until you get it just right. Observe the desired effect on the image in the main image window.One of the most essential functions of an image editor is to let you move sections of your image around. The selected layer will be marked with a different color than the other layers.ĭrag the selected layer up or down at the bottom of the layer until you are where you want it. Identify the layer you want to move to another location and click on it to select it. Note the order of the layers, with the top layer on top as if the layers were a pile of paper lying on your desk. Open the Layers Docker by clicking “Windows” on the top menu bar, selecting “Plugable Windows,” and then clicking “Layers” from the menu that appears on the side. Then you'll see the article dotted rather than a full layer, making it easier to navigate. ![]() If the layer is the same size as the entire image and contains transparent areas around the edge, you can select “layer” in the top menu bar and click “Auto Crop Layer” to get rid of the edges. If it also contains a hand pointing in a certain direction, you may have selected the wrong layer.Ĭlick and drag the item to the desired location. You'll know for sure you've selected the right layer if the move tool only contains a four-headed arrow and a normal cursor arrow. Hold the Move tool over the item you want to move. The “Move” tool looks like a four-pointed arrow. Select the layer that contains the element you want to move by clicking on that layer in the Layers Bar. ![]() Dock layers will by default be to the right of the image window in a separate window, but you can go anywhere you want. Then click “Layers” on the menu that appears on the side. Open the Layers Plugin by clicking on “Windows” in the top menu bar at the top of the image window and selecting “Plugable Windows”. But you need to understand the difference between moving an object from side to side while keeping it on the same layer and rearranging the layers so that they are in a different order. You can achieve interesting effects by reducing the opacity of the layer or using the blending functions. Layers are a powerful feature of the GIMP graphics program because they allow you to move elements independently of other elements.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |